faqs.org - Internet FAQ Archives

RFC 5331 - MPLS Upstream Label Assignment and Context-Specific L


Or Display the document by number




Network Working Group                                        R. Aggarwal
Request for Comments: 5331                              Juniper Networks
Category: Standards Track                                     Y. Rekhter
                                                        Juniper Networks
                                                                E. Rosen
                                                     Cisco Systems, Inc.
                                                             August 2008

    MPLS Upstream Label Assignment and Context-Specific Label Space

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Abstract

   RFC 3031 limits the MPLS architecture to downstream-assigned MPLS
   labels.  This document introduces the notion of upstream-assigned
   MPLS labels.  It describes the procedures for upstream MPLS label
   assignment and introduces the concept of a "Context-Specific Label
   Space".

Table of Contents

   1. Introduction ....................................................2
   2. Specification of Requirements ...................................2
   3. Context-Specific Label Space ....................................2
   4. Upstream Label Assignment .......................................3
      4.1. Upstream-Assigned and Downstream-Assigned Labels ...........4
   5. Assigning Upstream-Assigned Labels ..............................5
   6. Distributing Upstream-Assigned Labels ...........................5
   7. Upstream Neighbor Label Space ...................................6
   8. Context Label on LANs ...........................................9
   9. Usage of Upstream-Assigned Labels ..............................10
   10. Security Considerations .......................................10
   11. Acknowledgements ..............................................11
   12. References ....................................................11
      12.1. Normative References .....................................11
      12.2. Informative References ...................................11

1.  Introduction

   RFC 3031 [RFC3031] limits the MPLS architecture to downstream-
   assigned MPLS labels.  To quote from RFC 3031:

   "In the MPLS architecture, the decision to bind a particular label L
   to a particular Forwarding Equivalence Class (FEC) F is made by the
   Label Switching Router (LSR) which is DOWNSTREAM with respect to that
   binding.  The downstream LSR then informs the upstream LSR of the
   binding.  Thus labels are "downstream-assigned", and label bindings
   are distributed in the "downstream to upstream" direction."

   This document introduces the notion of upstream-assigned MPLS labels
   to the MPLS architecture.  The procedures for upstream assignment of
   MPLS labels are described.

   RFC 3031 describes per-platform and per-interface label space.  This
   document generalizes the latter to a "Context-Specific Label Space"
   and describes a "Neighbor Label Space" as an example of this.
   Upstream-assigned labels are always looked up in a context-specific
   label space.

2.  Specification of Requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3.  Context-Specific Label Space

   RFC 3031 describes per-platform and per-interface label spaces.  This
   document introduces the more general concept of a "Context-Specific
   Label Space".  An LSR may maintain one or more context-specific label
   spaces.  In general, labels MUST be looked up in the per-platform
   label space unless something about the context determines that a
   label be looked up in a particular context-specific label space.

   One example of a context-specific label space is the per-interface
   label space discussed in RFC 3031.  When an MPLS packet is received
   over a particular interface, the top label of the packet may need to
   be looked up in the receiving interface's per-interface label space.
   In this case, the receiving interface is the context of the packet.
   Whether MPLS packets received over a particular interface need to
   have their top labels looked up in a per-interface label space
   depends on some characteristic or configuration of the interface.

   Per-interface label space [RFC3031] is an example of a context-
   specific label space used for downstream-assigned labels.  Context-
   specific label spaces can also be used for upstream-assigned labels,
   as described below.

   When MPLS labels are upstream-assigned, the context of an MPLS label
   L is provided by the LSR that assigns the label and binds the label
   to a FEC F for a Label Switched Path (LSP) LSP1.  The LSR that
   assigns the label distributes the binding and context to an LSR Lr
   that then receives MPLS packets on LSP1 with label L.  When Lr
   receives an MPLS packet on LSP1, it MUST be able to determine the
   context of this packet.

   An example of such a context is a tunnel over which MPLS packets on
   LSP1 may be received.  In this case, the top label of the MPLS
   packet, after tunnel decapsulation, is looked up in a label space
   that is specific to the root of the tunnel.  This does imply that Lr
   be able to determine the tunnel over which the packet was received.
   Therefore, if the tunnel is an MPLS tunnel, penultimate-hop-popping
   (PHP) MUST be disabled for the tunnel.

   Another example of such a context is the neighbor from which MPLS
   packets on LSP1 may be received.  In this case, the top label of the
   MPLS packet, transmitted by the neighbor on LSP1, is looked up in a
   "Neighbor-Specific Label Space".

   The above two examples are further described in Section 7.

   There may be other sorts of contexts as well.  For instance, we
   define the notion of an MPLS label being used to establish a context,
   i.e., identify a label space.  A "context label" is one that
   identifies a label table in which the label immediately below the
   context label should be looked up.  A context label carried as an
   outermost label over a particular multi-access subnet/tunnel MUST be
   unique within the scope of that subnet/tunnel.

4.  Upstream Label Assignment

   When two MPLS LSRs are adjacent in an MPLS Label Switched Path (LSP),
   one of them can be termed an "upstream LSR" and the other a
   "downstream LSR" [RFC3031].  Consider two LSRs, Ru and Rd, that have
   agreed to bind Label L to a FEC F for packets sent from Ru to Rd.
   Then, with respect to this binding, Ru is the "upstream LSR", and Rd
   is the "downstream LSR"."

   If the binding between L and F was made by Rd and advertised to Ru,
   then the label binding is known as "downstream-assigned".  RFC 3031
   only discusses downstream-assigned label bindings.

   If the binding between L and F was made by Ru and advertised to Rd,
   then the label binding is known as "upstream-assigned".

   If the binding between L and F was made by a third party, say R3, and
   then advertised to both Ru and Rd, we also refer to the label binding
   as "upstream-assigned".

   An important observation about upstream-assigned labels is the
   following.  When an upstream-assigned label L is at the top of the
   label stack, it must be looked up by an LSR that is not the LSR that
   assigned and distributed the label binding for L.  Therefore, an
   upstream-assigned label MUST always be looked up in a context-
   specific label space, as described in Section 7.

   We do not require any coordination between the upstream label
   assignments and the downstream label assignments; a particular label
   value may be upstream-assigned to one FEC and downstream-assigned to
   a different FEC.

   The ability to use upstream-assigned labels is an OPTIONAL feature.
   Upstream-assigned labels MUST NOT be used unless it is known that the
   downstream LSR supports them.

   One use case of upstream-assigned labels is MPLS multicast, and an
   example of this is provided in Section 9.

4.1.  Upstream-Assigned and Downstream-Assigned Labels

   It is possible that some LSRs on an LSP for FEC F distribute
   downstream-assigned label bindings for FEC F, while other LSRs
   distribute upstream-assigned label bindings.  It is possible for an
   LSR to distribute a downstream-assigned label binding for FEC F to
   its upstream adjacent LSR AND distribute an upstream-assigned label
   binding for FEC F to its downstream adjacent LSR.  When two LSRs, Ru
   and Rd, are adjacent on an LSP for FEC F (with Ru being the upstream
   neighbor and Rd the downstream neighbor), either Ru distributes an
   upstream-assigned label binding for F to Rd, or else Rd distributes a
   downstream-assigned label binding to Ru, but NOT both.  Whether
   upstream-assigned or downstream-assigned labels are to be used for a
   particular FEC depends on the application using the LSP.

   Any application that requires the use of upstream-assigned labels
   MUST specify that explicitly, or else it is to be assumed that
   downstream-assigned labels are used.  An application on an LSR uses a
   label distribution protocol to indicate to its peer LSRs whether a
   particular label binding distributed by the LSR uses upstream-
   assigned or downstream-assigned label.  Details of such procedures
   are outside the scope of this document.  In some cases, the decision

   as to which is used for a particular application may be made by a
   configuration option.

5.  Assigning Upstream-Assigned Labels

   The only requirement on an upstream LSR assigning upstream-assigned
   labels is that an upstream-assigned label must be unambiguous in the
   context-specific label space in which the downstream LSR will look it
   up.  An upstream LSR that is the headend of multiple tunnels SHOULD,
   by default, assign the upstream-assigned labels, for all the LSPs
   carried over these tunnels, from a single label space, which is
   common to all those tunnels.  Further, an upstream LSR that is the
   head of multiple tunnels SHOULD use the same IP address as the head
   identifier of these tunnels, provided that the head identifier of
   these tunnels includes an IP address.  The LSR could assign the same
   label value to both a downstream-assigned and an upstream-assigned
   label.  The downstream LSR always looks up upstream-assigned MPLS
   labels in a context-specific label space as described in Section 7.

   An entry for the upstream-assigned labels is not created in the
   Incoming Label Map (ILM) [RFC3031] at the upstream LSR as these
   labels are not incoming labels.  Instead, an upstream label is an
   outgoing label, with respect to the upstream LSR, for MPLS packets
   transmitted on the MPLS LSP in which the upstream LSR is adjacent to
   the downstream LSR.  Hence, an upstream label is part of a Next Hop
   Label Forwarding Entry (NHLFE) at the upstream LSR.

   When Ru advertises a binding of label L for FEC F to Rd, it creates a
   NHLFE entry corresponding to L.  This NHLFE entry results in imposing
   the label L on the MPLS label stack of the packet forwarded using the
   NHLFE entry.  If Ru is a transit router on the LSP for FEC F, it
   binds the ILM for the LSP to this NHLFE.  If Ru is an ingress router
   on the LSP for FEC F, it binds the FEC to the NHLFE entry.

6.  Distributing Upstream-Assigned Labels

   Upstream-assigned label bindings MUST NOT be used unless it is known
   that the downstream LSR supports them.  How this is known is outside
   the scope of this document.

   MPLS upstream label assignment requires a label distribution protocol
   to distribute the binding from the upstream LSR to the downstream
   LSR.  Considerations that pertain to a label distribution protocol
   that are described in [RFC3031] apply.

   The distribution of the upstream-assigned labels is similar to either
   the ordered LSP control or independent LSP control of the downstream-
   assigned labels.  In the former case, an LSR distributes an upstream-

   assigned label binding for a FEC F if it is either (a) the ingress
   LSR for FEC F, or (b) if it has already received an upstream label
   binding for that FEC from its adjacent upstream LSR for FEC F, or (c)
   if it has received a request for a downstream label binding from its
   upstream adjacent LSR.  In the latter case, each LSR, upon noting
   that it recognizes a particular FEC, makes an independent decision to
   bind an upstream-assigned label to that FEC and to distribute that
   binding to its label distribution peers.

7.  Upstream Neighbor Label Space

   If the top label of an MPLS packet being processed by LSR Rd is
   upstream-assigned, the label is looked up in a context-specific label
   space, not in a per-platform label space.

   Rd uses a context-specific label space that it maintains for Ru to
   "reserve" MPLS labels assigned by Ru.  Hence, if Ru distributes an
   upstream-assigned label binding L for FEC F to Rd, then Rd reserves L
   in the separate ILM for Ru's context-specific label space.  This is
   the ILM that Rd uses to look up an MPLS label that is upstream-
   assigned by Ru.  This label may be the top label on the label stack
   of a packet received from Ru or it may be exposed as the top label on
   the label stack, as a result of Rd popping one or more labels off the
   label stack, from such a packet.

   This implies that Rd MUST be able to determine whether the top label
   of an MPLS packet being processed is upstream-assigned and, if yes,
   the "context" of this packet.  How this determination is made depends
   on the mechanism that is used by Ru to transmit the MPLS packet with
   an upstream-assigned top label L to Rd.

   If Ru transmits this packet by encapsulating it in an IP or MPLS
   tunnel, then the fact that L is upstream-assigned is determined by Rd
   by the tunnel on which the packet is received.  Whether a given
   tunnel can be used for transmitting MPLS packets with either
   downstream-assigned or upstream-assigned MPLS labels, or both,
   depends on the tunnel type and is described in [RFC5332].  When Rd
   receives MPLS packets with a top label L on such a tunnel, it
   determines the "context" of this packet based on the tunnel on which
   the packet is received.  There must be a mechanism for Ru to inform
   Rd that a particular tunnel from Ru to Rd will be used by Ru for
   transmitting MPLS packets with upstream-assigned MPLS labels.  Such a
   mechanism will be provided by the label distribution protocol between
   Ru and Rd and will likely require extensions to existing label
   distribution protocols.  The description of such a mechanism is
   outside the scope of this document.

   Rd maintains an "Upstream Neighbor Label Space" for upstream-assigned
   labels, assigned by Ru.  When Ru transmits MPLS packets the top label
   of which is upstream-assigned over IP or MPLS tunnels, then Rd MUST
   be able to determine the root of these IP/MPLS tunnels.  Rd MUST then
   use a separate label space for each unique root.

   The root is identified by the head-end IP address of the tunnel.  If
   the same upstream router, Ru, uses different head-end IP addresses
   for different tunnels, then the downstream router, Rd, MUST maintain
   a different Upstream Neighbor Label Space for each such head-end IP
   address.

   Consider the following conditions:

      1) Ru is the "root" of two tunnels, call them A and B.

      2) IP address X is an IP address of Ru.

      3) The signaling protocol used to set up tunnel A identified A's
         root node as IP address X.

      4) The signaling protocol used to set up tunnel B identified B's
         root node as IP address X.

      5) Packets sent through tunnels A and B may be carrying upstream-
         assigned labels.

      6) Ru is the LSR that assigned the upstream-assigned labels
         mentioned in condition 5.

   If and only if these conditions hold, then Ru MUST use the same label
   space when upstream-assigning labels for packets that travel through
   tunnel A that it uses when upstream-assigning labels for packets that
   travel through tunnel B.

   Suppose that Rd is a node that belongs to tunnels A and B, but is not
   the root node of either tunnel.  Then Rd may assume that the same
   upstream-assigned label space is used on both tunnels IF AND ONLY IF
   the signaling protocol used to set up tunnel A identified the root
   node as IP address X and the signaling protocol used to set up tunnel
   B identified the root node as the same IP address X.

   In addition, the protocol that is used for distributing the upstream-
   assigned label to be used over a particular tunnel MUST identify the
   "assigner" using the same IP address that is used by the protocol
   that sets up the tunnel to identify the root node of the tunnel.
   Implementors must take note of this, even if the tunnel setup

   protocol is different from the protocol that is used for distributing
   the upstream-assigned label to be used over the tunnel.

   The precise set of procedures for identifying the IP address of the
   root of the tunnel depend, of course, on the protocol used to set up
   the tunnel.  For Point-to-Point (P2P) tunnels, the intention is that
   the headend of the tunnel is the "root".  For Point-to-Multipoint
   (P2MP) or Multipoint-to-Multipoint (MP2MP) tunnels, one can always
   identify one node as being the "root" of the tunnel.

   Some tunnels may be set up by configuration, rather than by
   signaling.  In these cases, the IP address of the root of the tunnel
   must be configured.

   Some tunnels may not even require configuration, e.g., a Generic
   Routing Encapsulation (GRE) tunnel can be "created" just by
   encapsulating packets and transmitting them.  In such a case, the IP
   address of the root is considered to be the IP source address of the
   encapsulated packets.

   If the tunnel on which Rd receives MPLS packets with a top label L is
   an MPLS tunnel, then Rd determines a) that L is upstream-assigned and
   b) the context for L, from the labels above L in the label stack.
   Note that one or more of these labels may also be upstream-assigned
   labels.

   If the tunnel on which Rd receives MPLS packets with a top label L is
   an IP/GRE tunnel, then Rd determines a) that L is upstream-assigned
   [RFC5332] and b) the context for L, from the source address in the IP
   header.

   When Ru and Rd are adjacent to each other on a multi-access data link
   media, if Ru would transmit the packet, with top label L, by
   encapsulating it in a data link frame, then whether L is upstream-
   assigned or downstream assigned can be determined by Rd, as described
   in [RFC5332].  This is possible because if L is upstream-assigned,
   then [RFC5332] uses a different ether type in the data link frame.
   However, this is not sufficient for Rd to determine the context of
   this packet.  In order for Rd to determine the context of this
   packet, Ru encapsulates the packet in a one-hop MPLS tunnel.  This
   tunnel uses an MPLS context label that is assigned by Ru.  Section 8
   describes how the context label is assigned.  Rd maintains a separate
   "Upstream Neighbor Label Space" for Ru.  The "context" of this
   packet, i.e., Ru's upstream neighbor label space, in which L was
   reserved, is determined by Rd from the top context label and the
   interface on which the packet is received.  The ether type in the
   data link frame is set to indicate that the top label is upstream-
   assigned.  The second label in the stack is L.

8.  Context Label on LANs

   For a labeled packet with an ether type of "upstream label
   assignment", the top label is used as the context.  The context label
   value is assigned by the upstream LSR and advertised to the
   downstream LSRs.  Mechanisms for advertising the context label will
   be provided by the label distribution protocol between the upstream
   and downstream LSRs.  The description of such a mechanism is outside
   the scope of this document.

   The context label assigned by an LSR for use on a particular LAN
   interface MUST be unique across all the context labels assigned by
   other LSRs for use on the same LAN.  When a labeled packet is
   received from the LAN, the context label MUST be looked up in the
   context of the LAN interface on which the packet is received.

   This document provides two methods that an LSR can use to choose a
   context label to advertise on a particular LAN.

   The first method requires that each LSR be provisioned with a 20-bit
   context label for each LAN interface on which a context label is
   required.  It is then left to the provisioning system to make sure
   that an assigned context label is unique across the corresponding
   LAN.

   The second method allows the context labels to be auto-generated, but
   is only applicable if each LSR on the LAN has an IPv4 address as its
   primary IP address for the corresponding LAN interface.  (If the LAN
   contains LSRs that have only IPv6 addresses for the LAN interface,
   then the first method is used.)

   Suppose that each LAN interface is configured with a primary IPv4
   address that is unique on that LAN.  The host part of the IPv4
   address, identified by the network mask, is unique.  If the IPv4
   network mask is greater than 12 bits, it is possible to map the
   remaining 20 bits into a unique context label value.  This enables
   the LSRs on the LAN to automatically generate a unique context label.
   To ensure that auto-generated context label values do not fall into
   the reserved label space range [RFC3032], the value of the host part
   of the IPv4 address is offset with 0x10, if this value is not greater
   than 0xFFFEF.  Values of the host part of the IPv4 address greater
   than 0xFFFEF are not allowed to be used as context labels.

   Consider LSR Rm (downstream) connected to Ru1 (upstream) on a LAN
   interface and to Ru2 (upstream) on a different LAN interface.  Rm
   could receive a context label value derived from the LAN interface
   from Ru1 and from Ru2.  It is possible that the context label values
   used by Ru1 and Ru2 are the same.  This would occur if the LAN

   interfaces of both Ru1 and Ru2 are configured with a primary IPv4
   address where the lowest 20 bits are equal.  However, this does not
   create any ambiguity, as it has already been stated that the context
   label MUST be looked up in the context of the LAN interface on which
   the packet is received.

9.  Usage of Upstream-Assigned Labels

   A typical use case of upstream-assigned labels is for MPLS multicast
   and is described here for illustration.  This use case arises when an
   upstream LSR Ru is adjacent to several downstream LSRs <Rd1...Rdn> in
   an LSP, LSP1 AND Ru is connected to <Rd1...Rdn> via a multi-access
   media or tunnel, AND Ru wants to transmit a single copy of an MPLS
   packet on the LSP to <Rd1...Rdn>.  In the case of a tunnel, Ru can
   distribute an upstream-assigned label L that is bound to the FEC for
   LSP1, to <Rd1..Rdn> and transmit an MPLS packet, the top label of
   which is L, on the tunnel.  In the case of a multi-access media, Ru
   can distribute an upstream-assigned label L that is bound to the FEC
   for LSP1, to <Rd1..Rdn> and transmit an MPLS packet, the top label of
   which is the context label that identifies Ru, and the label
   immediately below is L, on the multi-access media.  Each of
   <Rd1..Rdn> will then interpret this MPLS packet in the context of Ru
   and forward it appropriately.  This implies that <Rd1..Rdn> MUST all
   be able to support an Upstream Neighbor Label Space for Ru and Ru
   MUST be able to determine this.  The mechanisms for determining this
   are specific to the application that is using upstream-assigned
   labels and is outside the scope of this document.

10.  Security Considerations

   The security considerations that apply to upstream-assigned labels
   and context labels are no different in kind than those that apply to
   downstream-assigned labels.

   Note that procedures for distributing upstream-assigned labels and/or
   context labels are not within the scope of this document.  Therefore,
   the security considerations that may apply to such procedures are not
   considered here.

   Section 8 of this document describes a procedure that enables an LSR
   to automatically generate a unique context label for a LAN.  This
   procedure assumes that the IP addresses of all the LSR interfaces on
   the LAN will be unique in their low-order 20 bits.  If two LSRs whose
   IP addresses have the same low-order 20 bits are placed on the LAN,
   other LSRs are likely to misroute packets transmitted to the LAN by
   either of the two LSRs in question.

   More detailed discussion of security issues that are relevant in the
   context of MPLS and GMPLS, including security threats, related
   defensive techniques, and the mechanisms for detection and reporting,
   are discussed in "Security Framework for MPLS and GMPLS Networks
   [MPLS-SEC].

11.  Acknowledgements

   Thanks to IJsbrand Wijnands's contribution, specifically for the text
   on which Section 8 is based.

12.  References

12.1.  Normative References

   [RFC3031]  Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
              Label Switching Architecture", RFC 3031, January 2001.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC5332]  Eckert, T., Rosen, E., Aggarwal, R., and Y. Rekhter, "MPLS
              Multicast Encpsulations", RFC 5332, August 2008.

12.2.  Informative References

   [RFC3032]  Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
              Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
              Encoding", RFC 3032, January 2001.

   [MPLS-SEC] Fang, L., Ed., "Security Framework for MPLS and GMPLS
              Networks", Work in Progress, July 2008.

Authors' Addresses

   Rahul Aggarwal
   Juniper Networks
   1194 North Mathilda Ave.
   Sunnyvale, CA 94089

   EMail: rahul@juniper.net

   Yakov Rekhter
   Juniper Networks
   1194 North Mathilda Ave.
   Sunnyvale, CA 94089

   EMail: yakov@juniper.net

   Eric C. Rosen
   Cisco Systems, Inc.
   1414 Massachusetts Avenue
   Boxborough, MA 01719

   EMail: erosen@cisco.com

Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

 

User Contributions:

Comment about this RFC, ask questions, or add new information about this topic: